Crown XTI 2000 Power Amp

Crown XTI 2000 Power Amp
Product no.: AD1746
List Price: $699.99
Your price: $449.99
You save: $250.00 (35%)
FEATURES
  • Integrated proprietary DSP with LCD front panel display
  • Accurate, uncolored sound with very low distortion for the best in music and voice reproduction
  • Advanced protection circuitry guards against: shorted outputs, open circuits, DC, mismatched loads, general overheating, high-frequency overloads and internal faults
  • Extremely versatile, handling a wide range of speaker impedances and outputs
  • Switch-mode universal power supply
  • Speaker presets for crossover frequencies, EQ, limiting, and delay
  • All products fill 2U rack spaces and weigh under 17 pounds
  • Speakon® and binding post outputs, XLR inputs and loop-thrus
  • Comprehensive LED status per channel
  • 3-year, no-fault, fully-transferable warranty
SPECIFICATIONS
  • Voltage Gain at 1kHz, 8 ohm rated output:
  • XTi 1000: 30.5dB _XTi 2000: 32.9dB_XTi 4000: 34.2dB
  • Frequency Response: ±0.25 dB from 20 Hz to 20 kHz at 1 watt into 4 ohms
  • Phase Response (at 1 watt, 20 Hz to 20 kHz): ±15
  • Load Impedance: Safe with all types of loads. Rated for 2 to 8 ohms in Stereo mode, 4 to 16 ohms in Bridge-Mono mode
  • Sensitivity: 1.4V
  • Signal to Noise Ratio (below rated 1 kHz power at 8 ohms): _105 dB (A weighted).
  • Damping Factor: Better than 500 from 20 Hz to 500 Hz.
  • Crosstalk:
    > 80 dB below rated power, 20 Hz to 1 kHz.
  • Common Mode Rejection (CMR):
    > 45 dB from 20 Hz to 1 kHz._Input Stage: Input is electronically balanced and employs precision 1% resistors.
  • Input Impedance (nominal): 20 k ohms, balanced;10 k ohms, unbalanced.
  • Maximum Input Signal: +22 dBu typical
  • AC Line Voltage and Frequency Configurations Available: 100V, 120V, 220-240V _50/60 Hz
  • AC Line Current:
  • XTi 1000: 6.5A_XTi 2000: 6.9A_XTi 4000: 8.0A
  • At Idle: Draws no more than 90 watts.
  • Operating Temperature: 0 C to 40 C at 95% relative humidity (non-condensing).
  • DSP Section
  • EQ: 4-band paragraphic per channel, boost/cut ±12 dB. Also adjustable high and low shelving filters
  • Filters: Highpass and lowpass per channel. Butterworth 6/12/18/24 dB per octave. High and low shelving filters, one per channel
  • Delay: For signal alignment of driver; 5 mS total delay
  • Subharmonic Synthesizer: Adds low-frequency content
  • Output limiter: Prevents clipping
  • Presets: 10 user speaker presets
  • Front Panel Controls and Indicators
  • Level: Detented rotary level control, one per channel
  • Power Switch: On/off switch applies AC power to the amplifier
  • Sel/Prev/Next Buttons: Three buttons near the LCD screen are used to access menu items
  • LCD Screen: Backlit liquid crystal display shows speaker presets
  • Signal Indicator: Green LED, one per channel, flashes when a very low-level signal is present at input
  • ”10 Indicator: Green LED flashes when output signal exceeds ”10 dB below clip.
  • ”20 Indicator: Green LED flashes when output signal level exceeds ”20 dB below clip
  • Ready Indicator: Green LED, one per channel, illuminates when the amplifier is ready to produce audio
  • Clip Indicator: Red LED, one per channel, turns on at the threshold of audible distortion
  • Temp/Fault Indicator: Red LED, one per channel, illuminates under Fault or excessive temperature conditions
  • Power Indicator: Blue LED illuminates when the amplifier has been turned on and has power
  • Rear Panel Controls and Connectors
    • <